SM-360WD Automatic Washer-Disinfector

Technical Specification

Equipment category: Fixed

Machine size: 950*825*2060 mm (length*width*height)

Cleaning cabin size: 627*595*980 mm (length*width*height)

Total volume: 350L

Power supply: 3N～220V, 50Hz

Power: 31kVA

Ambient temperature: 5℃～40℃

Relative humidity: ≤80%

Atmospheric pressure range: 70kPa～106kPa

Water supply pressure: 0.2MPa～0.5MPa

Inlet water temperature: 5℃～40℃

Work cabin material: stainless steel 304

Load rack trolley material: stainless steel 304

Working noise: The working noise of the automatic cleaning and disinfection device is not greater than 75dB(A)

Usage: Mainly used for cleaning, disinfection and drying of endoscopes, scalpels, hemostats, tweezers and dental instruments.

Leveling device: In order to adapt to uneven floors, the equipment is equipped with a leveling device. The maximum allowable horizontal inclination angle of the cleaning and disinfection device is 5 degree

Main body insulation: ≥5mm thermal insulation cotton, which has the characteristics of low thermal conductivity, good fire resistance, strong anti-aging ability, non-toxic and environmentally friendly, high-end appearance and soft texture.

Display: 7 -inch color touch screen, communication rate ≥ 19.2Kbps

Automatic control system: Using human-computer interaction interface and Mitsubishi PLC, the control is precise, safe and reliable, one-click start to end, the whole process is automatically completed, the temperature and cleaning time are displayed, and the system can be maintained and upgraded

Printer: Use a micro printer to print various data of the entire cleaning process, which can be saved for a long time. It can print mode name, cleaning date, thermal bleaching A0 value data, cleaning time of each stage and end status and other information.

Multiple operating modes: The product has multiple built-in cleaning programs for users to choose, and is suitable for a variety of cleaning scenarios.

Water circulation pump: It adopts German Hanning brand water circulation pump, which has the characteristics of large flow, high flow rate and high temperature resistance, which can ensure sufficient water flow circulation during the cleaning process in the cabin.

High-pressure blower: A vortex-type high-pressure blower with large air volume, high wind speed and strong wind pressure is used to continuously supply flowing air into the cleaning cabin.

Hot air box: heats the flowing air flowing into the cleaning cabin

Air inlet filter: Use a high-efficiency filter to prevent the dry load air from being contaminated by microorganisms

Water heating: Use a high-power electric heating tube. The heating tube has a large contact area with water and the heating speed is fast. It can quickly heat to the set temperature value during the water circulation process.

Water spray system: There are rotating spray arms on each floor. The spray arms have optimized arrangement of spray holes. The designed angle and number can well cooperate with the rapid rotation of the spray arms to achieve the best cleaning effect. The water inlet of the circulating pump is installed . There is a filter to prevent the spray arm from clogging.

Cooling fan: A cooling fan is installed on the top of the machine to better remove the heat accumulated inside the machine.

Water supply and drainage system: Use braided hoses and water-adding solenoid valves, which can withstand normal water pressure and control the amount of water added. Use a drainage pump to discharge wastewater in the cleaning cabin. The unique S-shaped backflow design drainage pipeline prevents the backflow of wastewater.

Circulation pipeline: Use high-temperature resistant silicone tubes to connect the circulation pipeline, and apply glue to the joints installed in the cleaning cabin to prevent water leakage.

Cleaning agent filling: In order to ensure accurate measurement of the cleaning agent, a peristaltic pump is used for filling. A liquid level detection device is installed in the holding barrel to detect the remaining amount of chemical additives in the barrel. If the remaining cleaning agent is insufficient for the next cleaning, a screen will prompt the user to add cleaning agent.

Hatch design: manual double door. When the front door or back door is not closed, the equipment cannot operate, and the display prompts that the door is not closed. When the cleaning program is started and the operator opens the front or back door, the equipment automatically stops running, and The display shows that the door is not closed and the buzzer sounds an alarm. However, the doors on both sides of the sterilizer cannot be opened at the same time to prevent air convection.

Fault prompt: When there is insufficient enzyme, insufficient oil, insufficient disinfectant, abnormal wind heat, abnormal inner tank temperature, abnormal wind pressure, water addition timeout, drainage failure, the front/rear door is not closed, a buzzer will sound, and the machine screen will display an alarm message.

Temperature control device: The temperature sensor adopts PT1000 platinum resistance, with a measuring range of 0℃~200℃

Emergency stop device: Emergency stop devices are installed on the loading and unloading sides of the equipment to enable emergency power outage when the equipment fails.

Timing device: The time of each stage can be set and displayed through the touch screen. When the time is less than 5 minutes , the accuracy is ±2.5%; when it exceeds  5 minutes , the accuracy is ±1%.