VSM-530WK Automatic Washer-Disinfector

Technical Specification

Equipment category: fixed type

Outer box size: 1270 * 1000 * 2020 (L * W * H)

Cleaning compartment size: 693 * 828 * 935 (L *W * H)

Total volume: 536L

Power supply: 380V, 50Hz

Power: 40kVA

Environmental temperature: 5 ℃~40 ℃

Relative humidity: ≤ 80%

Atmospheric pressure range: 70kPa~106kPa

Water supply pressure: 0.2MPa~0.5MPa

Inlet water temperature: 5 ℃~40 ℃

Work cabin material: stainless steel 304

Load frame trolley material: stainless steel 304

Purpose: Mainly used for cleaning, disinfecting, and drying surgical instruments, glassware, anesthesia instruments, and plastic products

Main body insulation: ≥ 5mm insulation cotton, with low thermal conductivity, good fire resistance, strong aging resistance, and no Toxic, environmentally friendly, high-end appearance, soft texture, etc

Automatic control system: using human-machine interface and Siemens PLC, precise control, safe and reliable, One-click start to end, the entire process is automatically completed, displaying temperature and cleaning time, and the system can be maintained upgrade.

Printer: A micro printer is used to print the data of the whole cleaning process, which can be saved for a long time. It can print the mode name, cleaning date, heat drift A0 value data, cleaning time and end status of each stage

Operation mode (program): flexible control equipment, wide range of application, 6 cleaning modes, 3 key steps, 11 custom procedures

High pressure fan: using vortex high pressure fan, with high air volume, high wind speed and strong wind pressure, and continuously flow air into the cleaning tank

Air inlet filter: Use high-efficiency filter to prevent dry load air from being affected by microorganisms

Water spray system: each layer has a rotating spray arm, the spray arm has an optimized arrangement of spray holes, the design Angle, degree and quantity can be well with the spray arm rapid rotation, so that the cleaning effect to achieve the best, the circulating pump inlet is equipped with a filter screen, to prevent the spray arm blockage

Seal door: using tempered insulating glass sealed door, you can clearly observe the cleaning situation of the items in the cleaning cabin, the door structure is automatically opened up and down doors, save space. Double doors interlock and combined with two cylinders to seal the door, equipped with anti-clamp hand device and overload device, to maximize the safety of operators and equipment

Fault prompt: when the enzyme is insufficient, the water pressure is abnormal, the wind pressure is abnormal, the high and low temperature box water overtime, loading and the unloading door failure, it will sound beep, water heating and wind heating beyond the protection value, the machine screen display alarm information

Display: The loading door and unloading door are each installed with a communication rate of 19.2Kbps, 7-inch real color industrial touch screen. Through the touch screen, the loading door and unloading door can be turned on and off under certain working conditions, which is not only enough, can set and run the program, but also see the alarm record and the running time of each stage, so as to meet the visualization requirements of process control

High and low temperature water tank: the whole machine adopts the method of separate water supply from high and low temperature, and the control system pretreats in advance (the high temperature water tank is heated to about 40 degrees in advance, and the high temperature water tank is heated to about 80 degrees, depending on the system parameter setting). The purpose is to reduce the heating time of the cleaning and disinfection cycle, so as to shorten the running time of the whole program on the side

Heating system: mainly composed of heating pipe and heating fin. The heating pipe hethe pure water or distilled water in the storage tank to provide the heat source for the spray flushing; the heating fin mainly provides the heat source for the air inlet and plays the role of rapid drying instrument in the drying stage

Drying system: mainly composed of heat source, fan and ventilation pipeline. The powerful air flow generated by the fan is heated through the fin heating device, and fills the cleaning and disinfection chamber through the ventilation pipeline. The hot air flow forms a strong vortex air flow in the cleaning and disinfection chamber to dry the cleaned items.

Injection system: mainly composed of peristaltic pump, silicone hose, storage tank and liquid level floating ball. The peristaltic pump injects the cleaning agent, disinfectant and additional lubricant in the storage tank into the cleaning and disinfection chamber in stages to enhance the cleaning and disinfection effect.

Printing system: mainly composed of printer and communication cables. The relevant data generated during the operation of the equipment can be printed by the printer for easy archiving and access.